{"id":1463,"date":"2026-11-20T14:36:11","date_gmt":"2026-11-20T06:36:11","guid":{"rendered":"https:\/\/www.ypmfg.com\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/"},"modified":"2026-11-20T14:36:11","modified_gmt":"2026-11-20T06:36:11","slug":"can-a-laser-cut-a-0-5-mm-hole","status":"publish","type":"post","link":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/","title":{"rendered":"Kann ein Laser ein 0,5-mm-Loch schneiden?"},"content":{"rendered":"<div style=\"margin: 0 auto;padding: 20px;font-family: -apple-system, BlinkMacSystemFont, &#039;Segoe UI&#039;, Roboto, &#039;Helvetica Neue&#039;, Arial, sans-serif\">\n<blockquote style=\"margin: 1.6em 0;padding: 1.2em 1.5em;background: linear-gradient(90deg, #faf2f4 0%, #fff 100%);border-left: 4px solid #d05570;color: #444444;font-style: italic;border-radius: 0 8px 8px 0\">\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Laser cutting small holes in sheet metal works down to roughly 0.5 mm in thin stock (0.5\u20131 mm). Below that, or in thicker plate, dross and heat distortion make drilling or EDM a cleaner route.<\/p>\n<\/blockquote>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">You need a pattern of small holes\u2014filters, heat exchangers, perforated panels\u2014and you need them within tolerance without burr or distortion. The real question is whether a laser is the right tool at your hole size and material thickness, and what to verify before releasing a drawing. YPMFG handles this as part of its <strong style=\"font-weight: 600;color: #b32050\"><a href=\"\/de\/2026\/09\/03\/m03-code-in-der-cnc-steuerung-was-er-bedeutet-und-wie-man-ihn-richtig-einsetzt\/\" title=\"CNC-Bearbeitung\" target=\"_blank\">CNC-Bearbeitung<\/a><\/strong> and sheet metal cutting service, so the process choice is made with your spec in hand, not guessed.<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">\n<ul style=\"margin: 1.2em 0;padding-left: 1.8em;line-height: 1.9;list-style-type: disc\">\n<li style=\"margin: 0.5em 0;color: #222222\"><strong style=\"font-weight: 600;color: #b32050\">Minimum practical hole size<\/strong>: Roughly 0.5 mm in 1 mm or thinner sheet; dross risk climbs fast in thicker material.<\/li>\n<li style=\"margin: 0.5em 0;color: #222222\"><strong style=\"font-weight: 600;color: #b32050\">Hole-to-thickness ratio<\/strong>: A ratio below about 1:1 makes a clean laser cut unreliable on most machines.<\/li>\n<li style=\"margin: 0.5em 0;color: #222222\"><strong style=\"font-weight: 600;color: #b32050\">Verification step<\/strong>: Always request a cut-test coupon in your exact alloy and thickness before releasing production.<\/li>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\"><\/ul>\n<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">How Do Fiber and CO2 Lasers Compare for Small Holes?<\/h2>\n<table style=\"width: 100%;border-collapse: collapse;margin: 1.6em 0;border-radius: 10px 10px 0 0;overflow: hidden\">\n<thead>\n<tr>\n<th style=\"background: #9e1840;color: #fff;padding: 14px 16px;text-align: left;font-weight: 600;border: 1px solid #e0e0e0\">Dimension<\/th>\n<th style=\"background: #9e1840;color: #fff;padding: 14px 16px;text-align: left;font-weight: 600;border: 1px solid #e0e0e0\">Fiber Laser<\/th>\n<th style=\"background: #9e1840;color: #fff;padding: 14px 16px;text-align: left;font-weight: 600;border: 1px solid #e0e0e0\">CO2 Laser<\/th>\n<th style=\"background: #9e1840;color: #fff;padding: 14px 16px;text-align: left;font-weight: 600;border: 1px solid #e0e0e0\">Decision Threshold<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Hole 0.5\u20131 mm<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Clean, low dross in thin stock<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Slower, wider heat-affected zone<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Below 0.5 mm, switch to EDM<\/td>\n<\/tr>\n<tr>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Hole 1\u20133 mm<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Standard production range<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Acceptable for non-critical parts<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Above 3 mm, drilling is cheaper<\/td>\n<\/tr>\n<tr>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Hole 3\u20136 mm, 316 SS<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Fine with nitrogen assist<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Dross common on 316 and titanium<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">316 or Ti, prefer drilling<\/td>\n<\/tr>\n<tr>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Sheet &gt; 6 mm<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Dross and taper increase<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Not practical for small holes<\/td>\n<td style=\"padding: 12px 16px;color: #222222;border: 1px solid #e0e0e0\">Move to mechanical drilling<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">If your hole sits under 1 mm and your sheet is over 2 mm, plan on a secondary operation\u2014drilling or EDM\u2014after the laser pass. YPMFG can map that combined route when you send your drawing.<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">What Is the Smallest Hole a Laser Can Actually Cut?<\/h2>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\"><img decoding=\"async\" src=\"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg\" alt=\"laser cutting small holes in sheet metal_lasercutting_laser cutting small holes in sheet metal\" style=\"width: 100%;max-width: 960px;height: auto;display: block;margin: 1.8em auto;border-radius: 0px\"><\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\"><strong>The practical floor is around 0.5 mm in stock no thicker than 1 mm. Below that the kerf width approaches the hole diameter, and the cut becomes an etch rather than a clean through-hole. In 2 mm 304 stainless, 0.5 mm holes start producing visible dross on the exit side.<\/strong><\/p>\n<h3 style=\"font-size: 18px;font-weight: 600;margin: 1.2em 0 0.4em;color: #b32050;line-height: 1.4\">Why Kerf Width Sets the Floor<\/h3>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">A typical fiber-laser kerf is 0.1 to 0.2 mm. When your hole is 0.5 mm and the kerf is 0.15 mm, you lose 30 percent of the intended diameter to vaporized material. In 0.5\u20130.8 mm sheet the ratio improves, which is why that thickness range handles the smallest holes most cleanly.<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Check your kerf compensation file before releasing any drawing that calls for holes under 1 mm. If the supplier cannot show you the compensation value they will apply, ask before you commit.<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">Which Material and Thickness Combination Matters Most?<\/h2>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\"><strong style=\"font-weight: 600;color: #b32050\">Sheet metal thickness<\/strong> and alloy determine whether the cut stays clean. 6061 aluminum at 1 mm handles small holes well because it conducts heat evenly. 316 stainless at the same thickness needs higher assist-gas pressure to keep dross off the exit face. Mild steel sits in between.<\/p>\n<h3 style=\"font-size: 18px;font-weight: 600;margin: 1.2em 0 0.4em;color: #b32050;line-height: 1.4\">Reflectivity and Assist-Gas Choice<\/h3>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Aluminum below 1 mm reflects a meaningful share of the beam, which can damage the lens on machines not rated for it. 304 and 316 are optically safer but oxidize during cutting, leaving a brown discoloration on the exit side. YPMFG specifies the right assist gas\u2014nitrogen for aluminum, oxygen for mild steel, compressed air for stainless\u2014based on your material callout.<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Confirm your material spec on the drawing: alloy grade, temper, and exact thickness tolerance. A 0.1 mm thickness variation changes the dross outcome on a 1 mm hole.<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">How Do You Keep Small-Hole Quality Without Distortion?<\/h2>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Dross forms when the exit side cannot clear the molten material. The fix is faster travel speed, higher assist-gas pressure, and a shorter focal length. Distortion appears when many holes sit close together and heat builds up in the sheet.<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">\n<ul style=\"margin: 1.2em 0;padding-left: 1.8em;line-height: 1.9;list-style-type: disc\">\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\"><img decoding=\"async\" src=\"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/laser-cutting-manufacturing-process.webp\" alt=\"laser cutting small holes in sheet metal_laser cutting small holes in sheet metal_lasercutting\" style=\"width: 100%;max-width: 960px;height: auto;display: block;margin: 1.8em auto;border-radius: 0px\"><\/p>\n<li style=\"margin: 0.5em 0;color: #222222\"><strong style=\"font-weight: 600;color: #b32050\">Pulse-cut strategy<\/strong>: Cut each hole individually with a jump between them, not a continuous path, so the sheet cools between pulses.<\/li>\n<li style=\"margin: 0.5em 0;color: #222222\"><strong style=\"font-weight: 600;color: #b32050\">Hole spacing<\/strong>: Below 1.5 mm center-to-center on thin gauge, visible warp becomes likely.<\/li>\n<li style=\"margin: 0.5em 0;color: #222222\"><strong style=\"font-weight: 600;color: #b32050\">Test coupon<\/strong>: A coupon in your exact gauge and alloy is the only reliable pre-production check.<\/li>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\"><\/ul>\n<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">YPMFG runs a cut-test before production and photographs the exit side for your file. If the coupon shows dross, the parameters are adjusted before the full run.<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">When Should You Switch from Laser to Drilling or EDM?<\/h2>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">No. A laser is not the right tool when the hole is under 0.3 mm or when the sheet is over 6 mm and the hole is small relative to thickness. In those cases, <strong style=\"font-weight: 600;color: #b32050\">EDM drilling<\/strong> or a mechanical drill gives a cleaner,more predictable edge.<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">The cost crossover depends on volume. For a few hundred holes, drilling is cheaper because there is no setup programming. For thousands of small holes in a complex pattern, laser wins because there is no tool wear. EDM handles hardened steels and titanium where neither laser nor drill works well. If your part mixes a large pattern of 0.8 mm holes with a few 0.3 mm pilot holes, a combined laser-plus-EDM route is the most practical option.<\/p>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Send your hole-size distribution and total count; a process engineer can map the fastest and cheapest route.<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">How a Typical Small-Hole Part Moves Through a Laser Shop<\/h2>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Consider a perforated 304 stainless filter plate, 2 mm thick, with a 5 \u00d7 5 mm grid of 1.2 mm holes. Step one: DFM review flags the 1.2 mm hole at the 2 mm edge as a dross risk; the pattern is offset 0.5 mm from the edge. Step two: a cut-test coupon runs at two travel speeds; the faster pass clears dross. Step three: production run with nitrogen assist at 3-bar exit pressure. Step four: <strong style=\"font-weight: 600;color: #b32050\">FAI inspection<\/strong> on the first piece, sampling every 25th piece through the run. Exit-side photos are archived with the lot number.<\/p>\n<blockquote style=\"margin: 1.6em 0;padding: 1.2em 1.5em;background: linear-gradient(90deg, #faf2f4 0%, #fff 100%);border-left: 4px solid #d05570;color: #444444;font-style: italic;border-radius: 0 8px 8px 0\">\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Process Route Reference: YPMFG process library, reviewed against published tooling data. Client-specific data withheld per NDA.<\/p>\n<\/blockquote>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">Practical Questions Before Ordering Small-Hole Laser Parts<\/h2>\n<h3 style=\"font-size: 18px;font-weight: 600;margin: 1.2em 0 0.4em;color: #b32050;line-height: 1.4\">Can a Laser Cut a 0.2 mm Hole in 1 mm Steel?<\/h3>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">No. The kerf alone is wider than the hole. Use EDM or a mechanical micro-drill for anything under 0.3 mm in steel.<\/p>\n<h3 style=\"font-size: 18px;font-weight: 600;margin: 1.2em 0 0.4em;color: #b32050;line-height: 1.4\">Does Material Type Change the Minimum Hole Size?<\/h3>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">It does. 6061 aluminum reflects beam energy, raising the effective minimum. 316 stainless absorbs more, so the minimum stays closer to the machine&#8217;s optical limit.<\/p>\n<h3 style=\"font-size: 18px;font-weight: 600;margin: 1.2em 0 0.4em;color: #b32050;line-height: 1.4\">How Do I Know If My Drawing Is Laser-Feasible?<\/h3>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Send the material, thickness, hole diameter, and hole count to a <strong style=\"font-weight: 600;color: #b32050\">CNC-Bearbeitung<\/strong> shop for a 30-minute feasibility review. If the hole-to-thickness ratio is above 1:1, laser is almost always viable.<\/p>\n<h3 style=\"font-size: 18px;font-weight: 600;margin: 1.2em 0 0.4em;color: #b32050;line-height: 1.4\">What Tolerance Can I Expect on a 1 mm Hole?<\/h3>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Typically within a few hundredths of a millimeter, depending on material and machine. For anything tighter, ask the supplier to quote the <strong style=\"font-weight: 600;color: #b32050\">CNC-Bearbeitungstoleranz<\/strong> they can hold on that specific diameter.<\/p>\n<h2 style=\"font-size: 20px;font-weight: 600;margin: 1.4em 0 0.5em;color: #b32050;line-height: 1.4\">Getting the Right Small-Hole Part Without Guesswork<\/h2>\n<p style=\"margin: 1.25em 0;line-height: 1.9;font-size: 16px;color: #222222;text-align: justify;letter-spacing: 0.02em\">Matching hole size, material, and thickness to the right process saves you a rejected batch and a costly re-cut. Before you commit, send your drawing or specification to YPMFG. An engineer will flag any dross or distortion risk, recommend a test coupon, and confirm the tolerance your part actually needs. You receive a written process recommendation with the specific parameters to check, not a generic quote. No obligation, no minimum order\u2014just a clear answer on whether your small-hole pattern will come out clean.<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"<p>Laser cutting small holes in sheet metal works down to roughly 0.5 mm in thin stock (0<\/p>","protected":false},"author":1,"featured_media":1464,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[44],"tags":[406,537,627,1094,1153],"class_list":["post-1463","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog","tag-cnc-machining","tag-material-thickness","tag-sheet-metal","tag-laser-cutting","tag-hole-size"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.3 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Can a Laser Cut a 0.5 mm Hole?<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/\" \/>\n<meta property=\"og:locale\" content=\"de_DE\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Can a Laser Cut a 0.5 mm Hole?\" \/>\n<meta property=\"og:description\" content=\"Laser cutting small holes in sheet metal works down to roughly 0.5 mm in thin stock (0\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/\" \/>\n<meta property=\"og:site_name\" content=\"YP-MFG| Custom CNC Parts Made Exactly to Spec\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-20T06:36:11+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg\" \/>\n<meta name=\"author\" content=\"admin\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Verfasst von\" \/>\n\t<meta name=\"twitter:data1\" content=\"admin\" \/>\n\t<meta name=\"twitter:label2\" content=\"Gesch\u00e4tzte Lesezeit\" \/>\n\t<meta name=\"twitter:data2\" content=\"6\u00a0Minuten\" \/>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Kann ein Laser ein 0,5-mm-Loch schneiden?","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/","og_locale":"de_DE","og_type":"article","og_title":"Can a Laser Cut a 0.5 mm Hole?","og_description":"Laser cutting small holes in sheet metal works down to roughly 0.5 mm in thin stock (0","og_url":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/","og_site_name":"YP-MFG| Custom CNC Parts Made Exactly to Spec","article_published_time":"2026-11-20T06:36:11+00:00","og_image":[{"url":"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg","type":"","width":"","height":""}],"author":"admin","twitter_card":"summary_large_image","twitter_misc":{"Verfasst von":"admin","Gesch\u00e4tzte Lesezeit":"6\u00a0Minuten"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#article","isPartOf":{"@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/"},"author":{"name":"admin","@id":"https:\/\/www.ypmfg.com\/de\/#\/schema\/person\/1ad07d09a6f18573f3b764ab0b4a8484"},"headline":"Can a Laser Cut a 0.5 mm Hole?","datePublished":"2026-11-20T06:36:11+00:00","mainEntityOfPage":{"@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/"},"wordCount":1181,"commentCount":0,"image":{"@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#primaryimage"},"thumbnailUrl":"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg","keywords":["CNC Machining","Material Thickness","Sheet Metal","Laser Cutting","Hole size"],"articleSection":["Blog"],"inLanguage":"de","potentialAction":[{"@type":"CommentAction","name":"Comment","target":["https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#respond"]}]},{"@type":"WebPage","@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/","url":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/","name":"Kann ein Laser ein 0,5-mm-Loch schneiden?","isPartOf":{"@id":"https:\/\/www.ypmfg.com\/de\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#primaryimage"},"image":{"@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#primaryimage"},"thumbnailUrl":"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg","datePublished":"2026-11-20T06:36:11+00:00","author":{"@id":"https:\/\/www.ypmfg.com\/de\/#\/schema\/person\/1ad07d09a6f18573f3b764ab0b4a8484"},"breadcrumb":{"@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#breadcrumb"},"inLanguage":"de","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/"]}]},{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#primaryimage","url":"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg","contentUrl":"https:\/\/www.ypmfg.com\/wp-content\/themes\/mb\/images_nengli\/buchong-2.jpg","width":1191,"height":893},{"@type":"BreadcrumbList","@id":"https:\/\/www.ypmfg.com\/de\/2026\/11\/20\/can-a-laser-cut-a-0-5-mm-hole\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.ypmfg.com\/"},{"@type":"ListItem","position":2,"name":"Can a Laser Cut a 0.5 mm Hole?"}]},{"@type":"WebSite","@id":"https:\/\/www.ypmfg.com\/de\/#website","url":"https:\/\/www.ypmfg.com\/de\/","name":"YP-MFG | Ma\u00dfgefertigte CNC-Teile \u2013 exakt nach Spezifikation","description":"","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.ypmfg.com\/de\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"de"},{"@type":"Person","@id":"https:\/\/www.ypmfg.com\/de\/#\/schema\/person\/1ad07d09a6f18573f3b764ab0b4a8484","name":"admin","image":{"@type":"ImageObject","inLanguage":"de","@id":"https:\/\/secure.gravatar.com\/avatar\/5edfa2692bdacc5e6ee805c626c50cb44cebb065f092d9a1067d89f74dacd326?s=96&d=mm&r=x","url":"https:\/\/secure.gravatar.com\/avatar\/5edfa2692bdacc5e6ee805c626c50cb44cebb065f092d9a1067d89f74dacd326?s=96&d=mm&r=x","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/5edfa2692bdacc5e6ee805c626c50cb44cebb065f092d9a1067d89f74dacd326?s=96&d=mm&r=x","caption":"admin"},"sameAs":["http:\/\/127.0.0.57"],"url":"https:\/\/www.ypmfg.com\/de\/author\/admin\/"}]}},"permalink_manager":null,"_links":{"self":[{"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/posts\/1463","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/comments?post=1463"}],"version-history":[{"count":0,"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/posts\/1463\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/media\/1464"}],"wp:attachment":[{"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/media?parent=1463"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/categories?post=1463"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.ypmfg.com\/de\/wp-json\/wp\/v2\/tags?post=1463"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}