Use at least 1.5× the insert diameter as embedment depth in nylon or ABS. Below 1.2×, pull-out torque drops faster than most catalogs predict. Check ISO 286 thread engagement rules before locking a drawing.
When a plastic housing strips at the threaded insert,the root cause is a sizing or embedment decision made early in the part layout. Buyers lose lead time, scrap housings, and push rework into production. YPMFG engineers review insert-to-housing fit against published tooling data so the part survives its intended torque. The checks below prevent that failure before you release a drawing.
Key Takeaways
- Embedment depth: Below 1.2× insert diameter, pull-out torque drops by roughly 40 percent in most thermoplastics.
- Thread class: 2A/2B engagement keeps assembly fast but adds 15 to 20 percent more flank contact than 6g/6g.
- Material match: Nylon strips at a lower torque than ABS at the same embedment; the shift is application-dependent.
- Tooling lead time: A 3-day sample is feasible for standard threaded insert bores; custom undercuts add 5 to 7 days.

How Does Embedment Depth Set the Pull-Out Torque Limit?
Embedment depth is the single variable that separates a holding insert from one that strips. At 1.5× diameter, the thread flank carries most of the load through the full engagement length. Below 1.2×, the last thread row bears a disproportionate share of shear.
Short embedment also concentrates stress at the outermost thread. In Nailon and ABS, that stress peaks well above the material yield point long before the insert reaches its rated torque. The housing cracks radially, and the insert pulls free on the next assembly cycle.
As a rule, measure embedment from the bore floor to the housing surface. If the part has a snap-fit or clip ring, subtract that ring thickness from the available depth. The usable embedment may be 0.8 mm shorter than the drawing suggests.
What embedment cannot do: compensate for a bore that is 0.1 mm larger than specified. The insert will still engage, but the thread clearance becomes the weak link, not depth.

What Tolerance Should You Call Out on the Plastic Bore?
The bore tolerance controls how much thread flank actually contacts the insert. A bore that is too large lets the insert rock, spreading load unevenly across three of five threads. A bore that is too tight makes insertion force exceed what a manual driver can handle.
Para la mayoría de Mecanizado con CNC or injection-molded housings, a bore tolerance of ±0.05 mm around the nominal keeps assembly torque in the expected band. Below ±0.03 mm, mold or moldeo por inyección shrinkage can push the part out of spec on 5 percent of a run.
| Dimensión | Loose Fit (2B) | Close Fit (6g) | Decision Threshold |
|---|---|---|---|
| Assembly torque | Lower, faster assembly | Higher, slower insertion | Auto-insert machines prefer 2B |
| Pull-out margin | Reduces by ~15 percent | Full thread contact | High-vibration mounts need 6g |
| Coste de los utillajes | Standard tap or mold core | Tighter core, +10 to 20 percent tool cost | Volume above 10 000 units justifies it |
| Reusability | Insert strips first | Housing cracks first | Serviceable parts prefer 6g |
The close fit buys torque margin but costs more in tooling and slows the line. If the part goes into a consumer product with a two-second assembly window, 2B is the practical choice.
When Does a Plastic Threaded Insert Strip Under Cyclic Load?
Static torque ratings in catalogs assume a single tightening event. Cyclic vibration, thermal cycling, and shock loading shift the failure mode. The insert does not pull out cleanly; the plastic threads fatigue and shear at the root.
Three factors accelerate this. First, ABS and PC have higher creep than nylon under sustained torque, so the housing slowly deforms around the insert. Second, temperature above 60 °C reduces nylon’s shear strength by a measurable margin. Third, a bore chamfer that is too deep leaves less thread engagement than the drawing shows.
Design for the worst-case torque, not the nominal. If the assembly spec calls for 1.2 N·m, design the insert for 1.8 N·m pull-out. The 50 percent buffer absorbs creep, vibration, and a small tooling variation without stripping the housing.
What no insert can fix: a bore in a thin-walled housing (under 1.5 mm). The wall flexes, the thread gap opens, and torque leaks away. Thicken the wall or add a boss; changing the insert will not close the gap.
How Do Material and Temperature Shift the Insert Choice?
The housing material sets the maximum torque the insert can deliver. Nylon 6 and Nylon 66 give the highest shear strength per unit volume. ABS is roughly 20 percent lower. PC sits between the two but creeps more at sustained load.
Temperature is the hidden variable. A design that passes at 25 °C may strip at 70





