Anodizing grows oxide 8 to 25 microns on Type II finishes. Unmasked threads pick up that oxide and your fasteners will not seat. Mask every threaded feature before the tank, or accept a blocked bore.
You machined clean threads, sent the part to anodize, and got it back with stripped bores. The problem is not the Usinage CNC. It is the surface finish step nobody planned for. YPMFG sees this on assembly-critical brackets and housings far more often than on cosmetic panels. The fix is a masking protocol you lock down before the part leaves your shop.
Key Takeaways
- Oxide thickness: Type II anodizing adds 8 to 25 microns radially; a 1 mm thread loses functional fit if unmasked.
- Masking method: PTFE tape seals coarse threads to M8; class 2A internal threads need wax or thread-lock compound.
- Verification step: A go/no-go gauge check after masking catches most fit failures before the part enters the tank.
Masking Method Comparison
| Dimension | PTFE Tape | Masking Wax | Thread-Lock Compound |
|---|---|---|---|
| Thread range | M4 to M8, coarse | M3 and finer, class 2A | All sizes, repeat cycles |
| Adhesion risk | Peels at sharp 60-deg edges | Fills undercut corners | Adds 0.05 to 0.1 mm radial |
| Removal | Cold water rinse | Hot water or solvent | Ultrasound or mechanical |
| Best use case | Quick, low-volume batches | Complex internal threads | Production runs, repeatability |
Pick the method that matches your thread class and batch size. Cheapest on the shelf is not always the method that survives the tank cycle.

Why Do Anodized Threads Fail, and Does Masking Actually Fix It?
Anodizing is not a paint job. The oxide grows outward from the metal surface. Every unmasked thread crest and root gains thickness, which shrinks the internal bore and raises the effective pitch.
On a Type II finish the oxide layer lands between 8 and 25 microns, set by current density and electrolyte chemistry. A 1 mm thread has limited radial clearance. Add 12 microns of oxide at the root and the bolt no longer starts by hand. Class 2B internal threads tolerate under 15 microns of radial build before you lose free rotation.
The failure is not cosmetic. A blocked thread means assembly rework, stripped material,or a scrapped housing. Thirty seconds of masking costs a fraction of one anodize rework cycle. Check your drawing callout: if it says anodize over threads, you are already past the point of no return and must machine the thread after the finish.
Which Masking Methods Hold Up on Machined Threaded Holes?
Three methods dominate shop-floor practice: PTFE tape, shellac-based masking wax, and anaerobic thread-lock compound. Each has a physical limit you cannot argue around.
- PTFE tape: Conforms to threads from M4 to M8 at coarse pitch. It peels on sharp 60-degree chamfer edges and does not seal undercuts.
- Masking wax: Fills class 2A internal threads and undercuts. Needs a 20-minute cure before tank loading. Removes in hot water or a light solvent.
- Thread-lock compound: Medium-strength anaerobic bond. Adds roughly 0.05 to 0.1 mm radially. Removes in an ultrasound bath. Best for repeat production runs where tape would shift.
No masking method survives Type III hard anodize at 50 microns without delamination at the thread root. For hard anodize, machine the bore oversize and tap after the finish. That is the only reliable route.

How Do Thread Class and Tolerance Change Your Masking Decision?
A 6H internal thread and a 7H internal thread need different masking strategies even on the same part, because the radial clearance gap is the variable that decides whether oxide blocks the fit.
A 6H internal thread has tighter clearance. Wax or compound is the safer choice because the mask fills the micro-gap between crest and root. A 7H thread has enough room that PTFE tape often holds without shifting the effective pitch. If your drawing calls out a positional tolerance under ASME Y14.5, the masking compound adds 0.05 mm and can push the threaded hole out of its positional envelope. Confirm the datum scheme before you apply the mask.
Send the BOM and finish spec to YPMFG engineering for a review. They will confirm the mask method, the tolerance window, and whether a post-finish tap is the safer route for your particular thread class.
How a Threaded-Hole Masking Process Route Works Step by Step
For a typical machined bracket with M5 to M8 threaded holes going through a Type II anodize, the route runs in seven steps.
- Deburr and solvent-wipe the threads. Confirm no chip or swarf remains in the root.
- Apply the chosen mask: tape, wax, or compound. For wax, cure 20 minutes before handling.
- Visual check: no gaps at the thread entry chamfer, no mask bridging across the pitch.
- Go/no-go gauge one sample thread. If the go side is loose by more than one pitch, the mask is too thick.
- Load to the anodize tank. Track cycle time and current density on the job card.
- Post-anodize removal: cold rinse for tape, hot water for wax, ultrasound for compound.
- Re-gauge and inspect oxide color on the flanks. Log the result against the ISO 2768 general tolerance callout.
Process Route Reference: YPMFG process library, reviewed against published anodizing and tooling data. Client-specific results withheld per NDA.
Common Questions About Masking Threads Before Anodizing
Can I skip masking if the thread is only for internal assembly? No. Internal threads anodize just like external ones. If the mating fastener is bare metal, the oxide still blocks the bore. Mask it.
Does masking change the color on the threaded area? The masked thread stays bare metal. After removal it will not match the anodized flanks. If uniform appearance matters, skip the mask and tap the thread after the finish.
What is the smallest thread I can reliably mask? M2 and 2-56 sit at the edge. Wax works down to M2. PTFE tape does not conform below M3. Under M2, machine the thread after the anodize instead of masking.
Getting the Masking Right on Your Next Batch
The difference between a part that assembles and one that sits in rework is a thirty-second decision about how you protect the threads before the tank. If your drawing has threaded features plus an anodize callout, send the print and finish spec to YPMFG for an engineering review. We will confirm the mask method, the tolerance window, and the post-finish gauge check so the part clears assembly on the first pass, without a rework cycle.





