金属・プラスチック製カスタム部品。最短3日で出荷。

Mask Threaded Holes Before Anodizing

公開日:

Mask Threaded Holes Before Anodizing

Threaded holes need masking before タイプIIIアルマイト処理. An oxide film up to 150 microns will fill fine-pitch threads and strip the profile. Plug or seal each cavity before the electrolyte touches the metal.

You are sending a CNC-machined 6061アルミニウム part out for anodizing and the threaded holes are the weak link. Without sealing, the oxide grows inward and the threads no longer accept a fastener. The failure window is the 2 to 3 hours before the part touches the electrolyte.

YPMFG has seen batches rejected when a plug cracked during the rinse cycle or when a thread pitch was too fine for the coating to release. The anodizing tank is not where the problem starts. It starts in how you mask each threaded feature.

Key Takeaways

  • Thread pitch threshold: Internal threads coarser than 1 mm pitch often survive a standard cycle. Anything finer needs full cavity masking.
  • Plug material selection: The seal must resist a 60 °C hot rinse without cracking,swelling, or seizing the thread geometry.
  • Batch verification: Pull one masked thread per batch before shipping. A chipped or seized thread means the plug failed.

Masking Method Comparison

次元 PTFE Thread Plug Hot-Melt Wax Coating Decision Threshold
Thread pitch All pitches; best at 0.5 mm or finer Coarse threads at 1 mm and up Below 0.8 mm: use plugs
Material options Nylon, PTFE, silicone Hot-melt wax, epoxy mask PTFE rated above 100 °C
Blind vs through hole Seal both ends Seal one end only Through-hole: plug both ends
Removal Snap, unscrew, or peel Solvent wash or burn-off Solvent leaves residue on 5052

For M4-to-M8 parts in 6061, a PTFE plug from the machined side gives the cleanest release. Save wax for coarse threads where a plug will not seat flush.

Why Do Threaded Holes Need Masking Before 陽極酸化処理?

Every micrometer of oxide that grows into a thread cavity steals material from the thread profile. A standard oxide film thickness spec runs 25 to 150 microns, depending on current density and bath chemistry. For an M4 thread at 0.7 mm pitch, even the thin end of that range eats into the 0.35 mm thread depth.

shootingholes_masking threaded holes before anodizing_threaded

Where the Oxide Grows

The oxide adheres to the substrate and does not peel off the flanks. Once the thread form is partially consumed, a fastener will not seat or will cross-thread on every installation.

Coarse threads at 1.5 mm pitch or more have enough material in the root to absorb the loss. Fine threads below 0.7 mm pitch do not. That gap is where masking becomes mandatory.

If the oxide thickness exceeds 30 percent of your thread depth, the thread will not survive the cycle. Mask or reduce the spec.

One physical limit: even with perfect masking, the oxide still grows on the entry chamfer and the first 0.5 mm of thread. You cannot fully protect the thread top without also masking the bore surface, which is rarely practical.

Which Masking Method Fits Your Thread Size and Alloy?

The choice comes down to two variables: thread pitch and the alloy you are anodizing. Hot-melt wax masking works on 5052 and 6061 when the thread is M6 or larger. For M3 and M4, a PTFE thread plug seats more reliably because the wax cracks on removal.

Silicone caps suit blind holes. They press in from the machined side and hold without adhesive. The upper temperature limit is lower than PTFE, so silicone is not ideal for the hottest rinse cycles.

For through-holes, you must plug both the internal thread and the exit face. A single plug on one side leaves the opposite thread exposed to oxide growth.

7075 alloy grows oxide faster and harder than 6061. The same 50-micron spec will deform 7075 threads more, so masking becomes less optional on that material.

What Tolerances and Surface Conditions Affect Masking Quality?

Masking quality depends on the plug material, the thread tolerance class, and the flank surface roughness. All three interact, and a mismatch in any one lets oxide wick into the cavity.

Thread Tolerance and Surface Roughness

A thread machined to 6G or 6F tolerance per ISO 965 will seat a plug cleanly. At 6H, the plug sits loose and oxide migrates in along the gap.

threaded_masking threaded holes before anodizing_shootingholes

Flank roughness matters. A Ra of 1.6 microns grips a PTFE plug and resists removal. At Ra 0.8 microns, the plug releases more easily under the rinse cycle.

One hard limit: you cannot mask a thread that has already been anodized and then strip the old oxide. The thread form is gone. Masking must happen before the first cycle, not after.

How Do You Verify Masked Threads After the Anodizing Cycle?

Verification is a two-step check. Remove the plug or wax, then inspect the thread under 10× magnification. You are looking for oxide residue on the flanks and any chipped material at the thread root.

Inspection Sequence

  • Visual check at 10×: oxide residue, chipped roots, plug fragments
  • First-article inspection with a calibrated go-no-go gauge: full-length pass without binding
  • Batch sample: pull one thread per 50 parts and re-check

Blind holes deeper than 3 diameters need a borescope to inspect the thread root. You cannot see the bottom of the cavity without one, and that is where oxide creep is hardest to spot.

How a 5-Axis CNC Part Handles Threaded Hole Anodizing

A typical 5-axis CNC-machined 6061 bracket has six M5 blind threaded holes, two M8 through-holes, and one M3 counterbored hole. The spec calls for a 50-micron Type III film in dark gray.

Step-by-Step Masking Sequence

  1. Insert PTFE plugs into all M5 blind holes and both M8 through-hole pairs. Silicone cap on the M3 blind end.
  2. Dip-coat the thread relief and chamfer with thin wax to catch oxide at the entry point the plug cannot reach.
  3. After the cycle, remove plugs under cold water. A warm rinse softens PTFE. Run a go gauge on each thread before packing.

Process Route Reference: YPMFG process library, reviewed against published tooling and anodizing data. Client-specific part numbers and batch results withheld per NDA.

Common Questions About Masking Threaded Holes Before Anodizing

Can I skip masking on coarse M8 threads? No. A 50-micron film still removes material from each flank, and on a 1.25 mm pitch thread the loss is small but not zero. Mask if the spec calls for uniform engagement.

Will hot-melt wax survive a two-dip anodizing cycle? It cannot. The second dip reheats the wax to its melt point and it slumps into the groove. Use PTFE plugs for multi-dip specs.

Does the alloy change the masking requirement? 7075 grows oxide faster and harder than 6061. The same 50-micron spec deforms 7075 threads more. Check the oxide growth rate against your pitch before deciding.

How do I mask a through-hole threaded on both ends? Plug both ends. A single plug on one side leaves the exit thread exposed. Oxide will grow from the unmasked side and ruin the thread you can still see.

Choosing the Right Masking Method for Your Part

The cost of a batch rejection from unmasked threads far exceeds the 20 minutes it takes to plug six holes before the anodize. Start with your thread pitch and alloy, match them against the method table above, and confirm with a first-article inspection before committing to the full run.

You can send your part drawings and anodizing specification to YPMFG for an engineering review. The team will flag any thread that will not survive the specified oxide thickness. They will also suggest a plug material, an installation sequence, and the inspection step your quality team needs on arrival.

この記事をシェアする:
コメント
jaJapanese